•     Over 250 years of quality service

  •     Freepost on orders over £100

  •     Traditional Values, 21st Century Service

Adhesives & Cements

12 Item(s)

per page

  • Araldite Instant Clear

    Suitable for bonding all metals. Ensure the surfaces are clean and dry. Break of the resealable cap from between the syringe plungers and break off the end seal. Depress the plunger and this will release equal amounts from both syringes. Mix for at least 20 seconds, you will need only to eject enough material that you can mix within 3 minutes as it will then dry hard. Apply to both surfaces, remove any excess material with a sharp knife before it has entirely dried. When putting the joint together apply some pressure keep them joined together (use tape) for 4 minutes, it will be 2 hours before completely dry. Should be stored in a dry place at room temperature.
  • Araldite Rapid (Syringe Dispenser)

    Snap off the resealable cap from between the syringes and break off the end seal, depress the plunger and this will release equal amounts from both tubes (only dispense what you are going to use within 5 minutes, as it will go hard). Mix on a clean and disposable surface for at least 30 seconds. Ensure the metal to be joined is clean and dry. Join the surfaces carefully and remove any excess glue once partially set. During assembly keep the surfaces together (use tape) and apply slight pressure for about 20 minutes, allow 2 hours for complete setting. This is a long lasting and fast setting glue. Parts are able to be adjusted within 4 minutes.
  • Araldite Rapid

    Dispense equal amounts from the two tubes (only dispense what you are going to use within 5 minutes, as it will go hard). Mix on a clean and disposable surface for at least 30 seconds. Ensure the metal to be joined is clean and dry. Join the surfaces carefully and remove any excess glue once partially set. During assembly keep the surfaces together (use tape) and apply slight pressure for about 20 minutes, allow 2 hours for complete setting. This is a long lasting and fast setting glue. Parts are able to be adjusted within 4 minutes.
  • Araldite Standard (Syringe Dispenser)

    This glue is solvent free and is perfect for joining metals where adustment may be necessary due to its long working time. Parts are repositionable within 80 minutes. Ensure the surfaces to be joined are clean and dry. Snap off the resealable cap from between the syringe plungers and break off the end seal. Depress the plunger to squeeze out equal amounts from both tubes, only squeeze out what you can use within 90 minutes as after this time it will dry hard. Join the surfaces and remove any excess glue before dry. When you join together apply light pressure to keep together (use tape) keep together for at least 8 hours, it can take up to 14 hours before completely set.
  • Devcon 5 Minute

    This glue, suitable for use on precious metals is rapid setting and clear. Ensure surfaces to be joined are clear and dry. Pierce the ends of both tubes, squeeze oout equal amounts from both tubes onto a disposable surface. Mix thoroughly, only dispense what you can use in 8 minutes as it will dry hard. Keep surfaces pressed together for 8 to 10 minutes, the drying time can take up to 1 hour. Store in a dry environment.
  • Araldite Standard

    Ensure the surfaces to be glued are clean and dry. Mix equal amounts of both tubes, You should only mix what you can use within 3 minutes, otherwise you will waste the remainder as it will set hard. Apply a thin layer of the mix to one surface, join the other surface and hold tight together for at least 8 hours (use tape) full strength is guaranteed after 14 hours. This glue has a long working time, allowing materials to be re-adjusted for up to 80 minutes. Should be kept in a dry place at room temperature.
  • Milliput Paste - Superfine White

    Milliput is an excellent putty suitable for precious metals. It is heat resistant up to 130ºC. . The 2 sticks once mixed is soft and highly adhesive and then gradually hardens. in normal temperature, Superfine Milliput will become hard within 3 hours. After setting hard Milliput continues to cure and is fully cured after the time equal to the setting time. There is no shrinkage during setting. It is very important that you use equal amounts when mixing from both sticks. Can be used for moulds and model making. Full instructions included.
  • G-S Hypo cement

    The tube has a built in applicator. This cement sets in 10 minutes and allows for adjustment until this time. Ensure surfaces are completely clean and dry. Move the applicator along the surface, the cement will be tacky after 20 seconds, assemble the surfaces at this point. It will be dry after 1 hour and can take up to 24 hours to completely set. Full instructions for use provided. Ideal for stone setting. Store in a dry environment.
  • Loctite Gel Superglue 5g

    This is a very popular jewellers cement, used for stone setting. For best results ensure 6 to 8 hours for setting time. Use a solder pick to apply (TOOLSSA125 - set of 3 picks) it is easy to manipulate the stone before it is set.
  • Vitalbond

    Ensure surfaces are clean and dry. Apply to one surface and press together, keep together with light pressure for 60 seconds, it can take up to one hour before fully dry.
  • Bostik All-Purpose Clear

    All surfaces to be glued must be clean and dry. When applying to precious metals, glue should be applied to both surfaces. Allow surfaces to dry for about 10 minutes and then press together. Keep tube stored in a dry place - solvents in the glue may damage some surfaces - test on a small area first.
  • Milliput Paste - Standard

    Milliput is an excellent adhesive suitable for precious metals. It is heat resistant up to 130ºC. It is not intended for use as a thin layer adhesive and should not be used where a thin glue has been indicated. The 2 sticks once mixed is soft and highly adhesive and then gradually hardens. in normal temperature, Milliput will become hard within 4 hours. After setting hard Milliput continues to cure and is fully cured after the time equal to the setting time. There is no shrinkage during setting. Can be used as a jewellery cement and for mould making. Full instructions included.

12 Item(s)

per page